Subscribe RSS
Home > Please Help > Please Help On WRH54G Router Client Configuration.

Please Help On WRH54G Router Client Configuration.

Finally I opend the chasis to close the reset contact manually because I thought the reset switch was broken. lanmedic, Aug 10, 2005 #62 Lampei Network Guru Member Sveasoft 1.04 Lampei, Aug 11, 2005 #63 lanmedic Network Guru Member Which firmware from Sveasoft: Alchemy, Satori, Talisman? Because, my client want to use remote access of these 3 server. AwAk3e Networking Support 1 03-09-2011 03:42 PM Help with VOIP router and Wireless Router Configuration Hey fellas?

I haven't tried to change any passwords recently. Is designed for enterprise networks, and requires a RADIUS authentication server. Will this lynksys AP work in this case? Excellent post there.

stuck here please help. 1:33 AM, March 30, 2010 Anonymous said... I was able to configure two routers which have been lying unused for a long time (because I could never find the right procedure) using this. 12:48 PM, February 19, 2010 Thanks. lio256, Apr 11, 2005 #30 GPz1100 Network Guru Member To the OP, Very nice detailed writeup of how to get this working.

The other one doesn't. Thanks again, Carrera206 shah said: carrere206: You don't need static IPs from your ISP for the guide, not sure what led you to believe that. Once again thank you so much and keep up the good work techsupport team. The TiVo is on the BRIDGE and the two don't see each other.

You can now turn to your wireless PC or laptop to connect it to the wireless network. Unfortunately, it appears the Linksys/Alchemy code when set to client mode does not pay any attention to the “access restriction†option. lio256, Apr 9, 2005 #27 shah Network Guru Member joebloggs said: Regarding A1, can you run a wire from that one port to another wireless router and thus be able to Should work unless there is something particular to the WRH54g router._________________SIG: I'm trying to teach you to fish, not give you a fish.

Please help. 2:33 PM, February 08, 2008 Anonymous said... Hi Socrates,Thanks a ton for this article. Does this seem right? By default in the setup page under Network Setup, Configuration type is set to Static IP, leave it as it is or if your router has different Network settings (ex.,

Configure IAS Now that we've installed IAS, we need to configure it. You will definitely need a computer to configure the WAP as an AP Client. 2 points to remember, make sure u know the wireless mac address of ur source (WRT54G), normally In this case, clients would get DHCP configuration from some other DHCP server, and could be accessed by other clients on the network. A wireless dlink router - DIR-655. 2.

some times its fine other times i have to unplug the ap and plug it back in before i can get online again. subnet that the xbox has now . I have a static route set up on the ROUTER with destination, subnet, gateway With this configuration, I can ping the tivo from the ROUTER connected computer. My problem is that I have no internet access on Router B.

It all seems to be working great, I can ping everything from everything. if router is now, WAP54G must be Most routers come pre-configured with dynamic ip assignments starting from *.*.*.100 or *.*.*.50 onwards. Is there a way to configure it so that both computers can connect to the internet at the same time?

Anyway, my top priority is to get WPA working with this setup. hth Ingo says: at @John Davies - I experienced the same issue on a Linksys WET101 WLan bridge. I am not sure its present on your ver 1.Note that WPA and WPA2 require that ALL devices on the wireless net be set to them -- clients, the wireless router

I entered the MAC address of the new laptop but still not able to connect.

The Viera has an ethernet port, but is quite a ways from my router (for a wired connection). Here I have all at the ...1....subnet PC Router Client XBox Do´in it this way I have internetconnection with my xbox. Bo says: at I have a Motorola dsl wireless modem from att upstairs in my office and a linksys wap54g downstairs connected by a switch for wireless. Admins, you may want to make this a sticky topic.

but i really dunno how to thank u for ur efforts to share this on blog n saving poor "IT - less" souls lk me.. :Pi ws tired of seeing my jkayca says: at Hi there, I'm trying to setup a wireless bridge from my router (WRT54GL) to a WAP54G access point. In this two-part series, David Davis walks you through the process. Validate or obtain the above information about the ROUTER.

But I am curious why you can't stream to your xbox. I have a netgear WGR614v5 router which I have been using with Airtel broadband (gurgaon) since 4 yrs now. This wiMax device (Samsung SMT-S3500), does not have option for wirless access. Set Wireless Network.Wireless Mode = Client 3.

Cheers SHAH shah, Apr 3, 2005 #18 lio256 Network Guru Member Cannot reach CLIENT from ROUTER Thanks Shah that was an excellent guide however I still have a few unresolved I hope any one can helps me! Set Wireless Security.WEP Encryption = 64 bits 10 hex digits 5. Patrick says: at Ok, I need to hook up a Panasonic Viera TC-P46G10 to my home network.

This also works great (because I can enter the ip of the computer directly).


© Copyright 2017 All rights reserved.