Subscribe RSS
Home > Black Screen > Vista Ultimate Install No Video After POST

Vista Ultimate Install No Video After POST


Even moreso certain models. "Resetting the entire Windows Update Component manually" I did this using the command prompt as outlined in the article. Once it reboots after initial re install it goes back to doing the same thing. For now, the goal is simply to get a clean install of Windows Vista up and running, with full hardware support and a configured AV solution.

by mikeyb61 / May 6, 2010 9:47 AM PDT In reply to: Black Screen Vista!!! Thanks in advance for your help!)I recently purchased a laptop from a reputable local dealership. View all 8 comments Report spectre- Aug 21, 2008 at 09:25 PM Thanks for the solution. Restarted twice {to be sure} and it was fixed.

Computer Screen Goes Black After Startup Windows 7

With Windows Vista, it's much simpler: All you have to do is copy the executables into a special folder on the install disk. The boot files are system files and will be hidden unless you have unchecked Hide protected operating system files when configuring Explorer. in this case, type in 1 then enter. I found the same links, but could not locate the easy transfer utility (7" EEE screen wasn't helping) and decided to just wing it.

But, I do not have nvidia, I`ve ati gpu and asus board. To keep it organized, I have a lot of subfolders including one for Apps and one for Drivers. It kept running. Black Screen After Installing Nvidia Driver The most crucial, as mentioned above, is your networking hardware: If your networking hardware works, and Vista is connected to the Internet, it will automatically begin downloading any required updates, including

I also kept checking to see if anything had appeared on the screen. Black Screen After Welcome Windows 7 Does anyone have any ideas? I checked my video drivers using the automated search feature, and found out that my drivers were up to date. original site I then scanned for adware and viruses, which there were none each time.

You can replace your existing installation, even from within the existing installation, or you can load Windows onto a different partition that you prepared in item four. Windows Xp Black Screen After Logo For extra memory, which this model seems to need, I am using a 32 GB USB flash drive...where I had backed up all my previous files from my last laptop which We're going to spend more time on these tasks in a future part of this series. As mentioned just remove it via Device manager.

Black Screen After Welcome Windows 7

Check for Updates took maybe 7 hours and still was not finished. Read More Here That said, you can always manually try to backup everything important. Computer Screen Goes Black After Startup Windows 7 Don't do it before a term paper is due or your business presentation slide show. Windows 10 Black Screen After Boot You can also look at your installed programs in Programs and Features located in the Control Panel.

Tested it numerous times, and found out it was a defective 500 GB hard drive that I had just installed. check my blog No Windows Logo, no errors, no flashing, absolutely nothing. Needless to say I'll be holding off wasting time installing the OS until it's finally baked...According to the latest reports, upgrades will run on your Windows 7 RC machine, but move Select the Inbox, Outbox, Sent Items, and Drafts. Windows 7 Loads To Black Screen With Cursor

I have the exact same issue as all of you. checking for updates was close to immediate and 20 updates were indicated ... 18 required and 2 optional. That value seems to increment on every occurrence, so maybe it is date related? this content lol AMD Athlon 64 processor 3800+ 2.41ghz 6GB Ram XP 32bit SP3 Helpful +2 Report sul Jul 30, 2008 at 06:42 AM helo my computer still goes to blank screen but

Normally I find the answers to my issues right away in these forums without having to ask a question. Windows 7 Install Black Screen After Restart Visual Studio? In this phase, you'll step through a series of steps in a wizard that will help you configure the Vista install so you can actually begin using it.

The discussion below is centered on those using Windows Update.

Helpful +25 Report teagle Jul 6, 2008 at 08:35 AM im having the same problem however nothing is displayed after the windows startup just a black screen I have tried starting The Windows Update Window will show that it is looking for updates, and then it will close. I was getting those continuous beeps which I read somewhere meant bad PSU, but I am hesitant to believe them because they only happened maybe twice out of 20-30 times of Black Screen After Installing Graphics Drivers I know, I was like "no way", but seriously after the reboot following the SP3 upgrade my video popped right up at the last-saved hi res setting, go figure.

Hope it helps somebody out there!!ARCSolo Flag Permalink This was helpful (0) Collapse - Black Screen and No cursor! Installed Webroot Spy Sweeper and Trend Micro Internet Security. 3. scottbirdseyMay 15, 2008, 3:44 AM meh, i took out one of the ram sticks and put the other in the a1 slot instead of a2, now it posts and boots vista the problem is not the pc or vga,vista 64 have proublems ro recognize monitors.i hope this help.

Proffitt Forum moderator / January 24, 2010 12:47 AM PST In reply to: DiscomBOBulated I'll keep on sharing how I recovered. Everything was still smooth, POST ran through without a hitch, windows splash screen came up then it went blank, but I could hear through the speaker that normal processes were running but i'm only running a Windows XP SP2 OS. After the process is done, you get the option for very detailed report.

I think mine got corrupted through a defrag I did earlier. michael Report stan› dusty - Nov 28, 2008 at 09:16 AM Thanks Dusty, I had to set the jumper from CS to maaster and it worked. Next, I ran Easy Transfer from the Windows 7 Start Menu. I did upgrade my UniBlue Registry Booster to the 2009 version, which helps.

If you have a vendor built computer, Windows Reinstall - OEM Computers is a must-read. RollercoasterTuesday, 04 August 2009 03:19:45 UTCIs it possible to transfer program installations? (Don\t know my question makes sense with two entirely different windows!), 04 August 2009 04:34:12 UTCScott, what was the Initially, it would work on an external monitor, but for the last 2 days, seemingly for no reason, when Windows begins to load, it attempts to go back to it's own Helpful +9 Report Darrian Nov 30, 2008 at 07:11 AM well I had the same problem I pushed the on/off button a few times and windows poped up, so give it

I was stumped. This is significantly faster than XP Setup. If you are not sure how to set a jumper just google it for directions and it should help, but hard drive a labeled. Now that all of Windows was gone, still no BIOS screen.We also had the other dead laptop after an update but that one was the famous DV6000.

But after a day or so, FireFox also started freezing up just like IE 7.So, not matter WHAT I have done, the browser still ultimately freezes up, and I still do and "Most recent checks for updates" says "never" ... Hey I hope if anyone of you who is planning to buy this crap hold on to your dollars and thread on more. The instructions that show up at this point (shown at right) have a section on "Upgrading from Windows XP." In that section there's a link to which is the one-stop-shopping

He has worked at companies like Hughes Aircraft and CSC, where he developed client/server-based applications. but that's hardware again since I had to do something with the hardware to get the BIOS screen to show.I know people are mightily upset over this but what good does If you do have Excel 2002 or later, secure your spreadsheet from hackers and then make sure you don't lose your password! Screen is black as hell and no bios no characters on the screen it's just black.


© Copyright 2017 All rights reserved.